Search This Supplers Products:Injection Mold Designplastic injection moldMolding ServiceCustom Moldcase molddie casting mold
- Home
- About us
- Products
- 3D printing & Prototype
- Home Appliances Plastic Mould/Molding
- Overmolding Mould/Molding
- Electronic Plastic Mould/Molding
- Medical Plastic Mould/Molding
- Industrial Plastic Mould/Molding
- Commodity Plastic Mould/Molding
- Auto plastic mould/molding
- Packaging Plastic Mould/Molding
- Stamping Mould & Die Casting
- Silicone Mould/Molding
- Blowing Mould/Molding
- Faqs
- Factory
- Mold tooling
- Mould steel
- Good Factory
- Plastic Material
- surface treatment
- Delivery time
- Payment terms
- Yunpeng advantage
- Yunpeng mould advantage 2
- 3D Drawing Format
- Yunpeng Certificate
- Service
- Manufacture plastic parts
- 3 D Printing
- Delivery Terms
- Die casting
- Quality
- Mold Wiki
- Mold Layout/Design
- Mold Layout Design
- do you know about" Injection molding"
- Mold Structure
- Mold problems
- Hot Runner
- Two shot plastic injection molding
- Cavity
- Parting Line
- How to Determine Parting Line of mold products?
- News
- YP mould
- Update news about our YP plastic injection mould
- How to get the injection products of the best prec
- Mold knowledge
- Customers visit our factory
- How to make injection mold with high qulaity?
- two shot plastic injection molding and it's functi
- Two shot plastic injection molding and it's functi
- What is a hot runner mold
- Certificate
- Contact us
why causes mold with hot runner leakage?
Is the leakage on the outside of the plastic injection mold or internally. Possible causes for external leaks are worn probe seals or improper cleaning when being maintenance. Internal leakage may be caused by shooting through when manifold in not fully up to temp or wear on the crush rings reducing the preload on the system.
There are several Hot Runner systems on the market and many causes for leakage. It would be helpful if you could be more specific with the type of system and location of leak. Also a great source for trouble shooting would be to contact the hot runner manufacturer since they are most familiar with their system(s) and the problems they may have.
In general:
I have seen hot runner internally flooded with plastic because injection molding parameters and settings are wrong. For example: mold cavity fill time too long, which causes the material to freeze up close to the injection points; then hold pressure applied onto frozen injection points—> the molten plastic has to go somewhere, maybe into your hot runner. A good symptom for this problem is if you have material leakage at the mainmould entry valve gate and plastic creeping back up your screw cylinder - because the molten material cannot get into the frozen cavity.
One specific situation:
There are several Hot Runner systems on the market and many causes for leakage. It would be helpful if you could be more specific with the type of system and location of leak. Also a great source for trouble shooting would be to contact the hot runner manufacturer since they are most familiar with their system(s) and the problems they may have.
In general:
I have seen hot runner internally flooded with plastic because injection molding parameters and settings are wrong. For example: mold cavity fill time too long, which causes the material to freeze up close to the injection points; then hold pressure applied onto frozen injection points—> the molten plastic has to go somewhere, maybe into your hot runner. A good symptom for this problem is if you have material leakage at the mainmould entry valve gate and plastic creeping back up your screw cylinder - because the molten material cannot get into the frozen cavity.
One specific situation:
if your hot runner has transfer gates to inserts, and these inserts are not currently in use. The transfer gates might need time to warm up to the same temperature, so they stay shut. Or check if these unused transfer gates are really well shut.
- if you need help, pls contact me, I am Tea, my email is injectionmold2006..........com
- whatsapp+8615958816137 skype：injectionmold2006..........com